Vwvortex Diy Replacing Driver Side Coolant Flange On A 2. remove the engine cover (if applicable), remove your air box and the tubing that connects it to the throttle body and set it to the side. 3. locate the coolant flange: 4. begin by removing all the wiring, connectors and small hoses from around the flange. Re: diy: replacing driver side coolant flange on a mkiv jetta 8v 2.o… (mross71) i hope it is ok that i replied to this post. i have used vw vortex for many years. the amount of info is amazing. i have never really needed to post a question before. my question is more for a sanity check. for about a week i have been loosing coolant.
Vwvortex Diy Replacing Driver Side Coolant Flange On A Re: diy: replacing driver side coolant flange on a mkiv jetta 8v 2.o… (mikewire) so, i just found out my water flange was crack by the base where it is bolted onto the engine on wednesday. i managed to get the part friday for a 12 dollars at the local european parts store. 8. now get the new flange and swap out the coolant sensor and o ring. old vs. new: coolant flange part # from ecstuning: remove clip and o ring from the old flange: replace clip and o ring and insert it into the new coolant flange: note: now would be a good time to replace that black top coolant sensor with the new green top. Joined. nov 15, 2001. location. monroe, nj. jan 21, 2010. #3. i am removing that part to drill and tap for the coolant temp. probe. for my gauges. i bought a new seal for the flange the part number is 037 121 688. i can see that mine is currently installed with black rtv. Remove the flange, clean the mating surface of the head, and put it all back together. fill it up with g12 water mix, run it, and top up as needed. easy job. now, another common coolant leak spot is the little bleed hose assembly that goes into the head, sort of behind the vacuum pump.
Vwvortex Diy Replacing Driver Side Coolant Flange On A Joined. nov 15, 2001. location. monroe, nj. jan 21, 2010. #3. i am removing that part to drill and tap for the coolant temp. probe. for my gauges. i bought a new seal for the flange the part number is 037 121 688. i can see that mine is currently installed with black rtv. Remove the flange, clean the mating surface of the head, and put it all back together. fill it up with g12 water mix, run it, and top up as needed. easy job. now, another common coolant leak spot is the little bleed hose assembly that goes into the head, sort of behind the vacuum pump. Abelonee the vdub head is back with a new video. sorry it had been a while cuz of work. here i replace the side coolant flange with a new one from o'reilly. There is a straight edge [cf diy 002] on either side of the cap; insert a flat screw driver and pop the cap off [cf diy 003] by prying up on the cap. after removing the engine cover you can see the coolant flange and temp sensor [cf diy 004]. step two: remove the air breather (aka snow box or air box) [cf diy 005]; disconnect the maf, intake.
Vwvortex Diy Replacing Driver Side Coolant Flange On A Abelonee the vdub head is back with a new video. sorry it had been a while cuz of work. here i replace the side coolant flange with a new one from o'reilly. There is a straight edge [cf diy 002] on either side of the cap; insert a flat screw driver and pop the cap off [cf diy 003] by prying up on the cap. after removing the engine cover you can see the coolant flange and temp sensor [cf diy 004]. step two: remove the air breather (aka snow box or air box) [cf diy 005]; disconnect the maf, intake.
Vwvortex Diy Replacing Driver Side Coolant Flange On A
Comments are closed.