How To Make A Drawstring Backpack вђў Crafting A Green World Gather up all your favorite playthings, and let’s go! 1. cut fabric to size. my kids are eight and ten, and these drawstring backpacks are sized to them. to make yours the same size, cut two pieces of exterior fabric and two pieces of inside lining fabric 12″x16″. cut two pieces of fabric on the bias at 2″x13″, and two pieces at 2. Reusable grocery bag. the tutorial calls for ripstop nylon yardage, but it’s not very hard to substitute a drawstring backpack or two, instead. for a small grocery bag, remove the nylon paracord and cut handles from the top of the bag, then serge them. for a larger bag, cut as many drawstring backpacks as you need apart at the seams, then.
How To Make A Drawstring Backpack вђў Crafting A Green World First, pin top handle to back of bag, 3.5” (8.9cm) from the sides and 2” (5cm) from the top. there should be a gap of about 1.5” (3.81cm) between the two ends of the handle. next, sew down handle to back of bag by sewing a rectangle with a “x”right below the drawstring channel. Step 14 how to insert drawstrings on the backpack. cut the cord into two pieces of 55" or 140 cm (small) or 65" or 165cm (large backpack) and use a safety pin or a bodkin to guide the first cord through the entire drawstring casing. both ends of the cord will come out of the same opening. Fold and press both of the long edges and one of the short edges by ¼ inch (0.64 centimeter). take one of the fabric pieces, and turn it so that the wrong side is facing you. fold both of the long edges and one of the narrow edges down by ¼ inch (0.64 centimeter). secure the edges with sewing pins, then iron them flat. Step 6. make the tabs for the bottom of the drawstring backpack using the 3 inch x 2 inch pieces of fabric. fold each piece of fabric in half, bring the wrong side of the fabric together with the right sides facing out. press flat with an iron. open up the fabric and you will see the pressed edge in the middle.
How To Make A Drawstring Backpack вђў Crafting A Green World Fold and press both of the long edges and one of the short edges by ¼ inch (0.64 centimeter). take one of the fabric pieces, and turn it so that the wrong side is facing you. fold both of the long edges and one of the narrow edges down by ¼ inch (0.64 centimeter). secure the edges with sewing pins, then iron them flat. Step 6. make the tabs for the bottom of the drawstring backpack using the 3 inch x 2 inch pieces of fabric. fold each piece of fabric in half, bring the wrong side of the fabric together with the right sides facing out. press flat with an iron. open up the fabric and you will see the pressed edge in the middle. Step 1: prepare the pattern for use. download the pattern and print it out in full size (print at 100%, no scaling on a us letter paper). tape the three sheets together, cut it out accordingly and remove the excess paper. you will get two pattern pieces. one for the bag and one for the cord tabs. Step 2: make tabs to go at the bottom of the bag. take the 2″ x 6″ rectangle and iron it in half lengthwise. open the rectangle up and fold each long side toward the crease you just made. iron these. then fold the rectangle in half again lengthwise and iron. you should end up with a 1 2″ x 6″ rectangle.
How To Make A Drawstring Backpack вђў Crafting A Green World Step 1: prepare the pattern for use. download the pattern and print it out in full size (print at 100%, no scaling on a us letter paper). tape the three sheets together, cut it out accordingly and remove the excess paper. you will get two pattern pieces. one for the bag and one for the cord tabs. Step 2: make tabs to go at the bottom of the bag. take the 2″ x 6″ rectangle and iron it in half lengthwise. open the rectangle up and fold each long side toward the crease you just made. iron these. then fold the rectangle in half again lengthwise and iron. you should end up with a 1 2″ x 6″ rectangle.
Comments are closed.