2008 Jeep Wrangler Bank 1 Sensor 2 Location 2906 posts · joined 2013. #3 · feb 7, 2021. so after doing a lot of research, i found that bank 1 is the passenger side and bank 2 is the driver side. sensor 1 on each side is the top, up stream sensor. sensor 2 is the lower, down stream sensor. i tried removing the lower o2 sensor on the passenger side today and it is a royal pain. 3.8 cyl1 is at the top of your driver side. on the 3.6 cyl1 is at the top of the passenger side. so is bank1 as well. 2018 jku sport s, a5, 4.56's, eaton rear locker, hybrid lift with rk 2.5" triple rate coils, fox 2.0 res 985 24 011 front fox 2.0 res 985 24 036 rear, clayton overland control arms (full set), clayton front tb, clayton ss relo.
2008 Jeep Wrangler Bank 1 Sensor 2 Location Your engine has three catalytic converters on it. two are directly below the intake exhaust manifolds, and the third is at the skid, by the transmission. there are four oxygen sensors two upstream in the cast exhaust manifold, and two downstream after the mini cats in the downpipe. bank 1 is the front of the engine, sensor 2 is downstream. In this video, i replace the o2 sensor in my 2014 jeep wrangler sahara, with the 3.6 pentastart engine. this is the bank 1 sensor 2, located on the passenger. Jeep wrangler p0137: o2 sensor low voltage (bank 1 sensor 2) p0137 is a fairly common obdii code that occurs in the jeep wrangler, it’s a general code. this means that it has the same meaning for any vehicle. this code is supposed to let you know that there is an issue with the wiring or harness going to the sensor, or the sensor itself is bad. You might get better responses over on the liberty forum. this is the grand cherokee forum and the exhaust systems are somewhat different. my best guess is bank 2 is the passenger side and sensor 1 is in front of that converter. this is assuming it has only 2 converters. 19 limited 4x4 3.6 white tan new daily driver.
2008 Jeep Wrangler Bank 1 Sensor 2 Jeep wrangler p0137: o2 sensor low voltage (bank 1 sensor 2) p0137 is a fairly common obdii code that occurs in the jeep wrangler, it’s a general code. this means that it has the same meaning for any vehicle. this code is supposed to let you know that there is an issue with the wiring or harness going to the sensor, or the sensor itself is bad. You might get better responses over on the liberty forum. this is the grand cherokee forum and the exhaust systems are somewhat different. my best guess is bank 2 is the passenger side and sensor 1 is in front of that converter. this is assuming it has only 2 converters. 19 limited 4x4 3.6 white tan new daily driver. The rear o2 sensor *is* the one after the cat as pointed out by x99j above, so replacing the front won't resolve this code. the p0138 high voltage code indicates an open in the rear sensor heater circuit. it may be a bad internal heater within the rear o2 sensor, you could check the heater wires (dark green white and black) for continuity. Jeep > 2008 > wrangler > 3.8l v6 > exhaust & emission > oxygen (o2) sensor. price: alternate: bank 1 sensor 2; actual oe part. ntk 23159. $26.79: $0.00 sold.
Arriba 44 Imagen 2008 Jeep Wrangler Bank 1 Sensor 2 Location The rear o2 sensor *is* the one after the cat as pointed out by x99j above, so replacing the front won't resolve this code. the p0138 high voltage code indicates an open in the rear sensor heater circuit. it may be a bad internal heater within the rear o2 sensor, you could check the heater wires (dark green white and black) for continuity. Jeep > 2008 > wrangler > 3.8l v6 > exhaust & emission > oxygen (o2) sensor. price: alternate: bank 1 sensor 2; actual oe part. ntk 23159. $26.79: $0.00 sold.
2008 Jeep Wrangler Bank 1 Sensor 2 Location
Comments are closed.